Nissan CONSULT 3 and CONSULT 4: A Shop Owner’s Guide
A 2019 Altima and a 2024 Rogue sit two bays apart. Same laptop, same Nissan subscription, same technician. The Altima opens in CONSULT-III plus and every module answers. The Rogue opens in the same software and the tool acts like the car is not there.
Nothing is broken. Nissan split its diagnostic software in two, and the Rogue belongs to the newer half. Shops that bought CONSULT-III plus a few years ago and never looked again are finding that line in the middle of their Nissan work.
Two Programs, One Laptop
CONSULT-III plus has been Nissan’s dealer diagnostic software for more than a decade. It covers Nissan and Infiniti vehicles from 1999 through current models: full-system DTC scans, bidirectional tests, module programming, EV and hybrid service, immobilizer and key work, and ADAS target calibrations when paired with the right interface.
CONSULT 4 came out for Nissan’s newest electronic architecture. It is web-based, it installs on the same PC as CONSULT-III plus, and it handles diagnostics and module programming on the vehicles built around that architecture. It does not replace the older program. Nissan says so directly. A Nissan bay now needs both, which is why the Nissan CONSULT 3 and CONSULT 4 subscription bundles them.
Which Vehicles Need CONSULT 4
The CONSULT 4 list is short today and grows with every model year:
- 2023 and newer ARIYA
- 2024 and newer Rogue
- 2025 and newer Kicks, Murano, and Armada
Nissan has added the 2025 and newer Pathfinder and the 2026 Sentra and Leaf as those models launched, and each redesign from here will probably land on the CONSULT 4 side. Every other Nissan and Infiniti still goes through CONSULT-III plus.
When Nissan redesigns a nameplate, the new generation moves to CONSULT 4 and the outgoing generation stays on CONSULT-III plus. A shop that works Rogues will have both generations in the lot for years. One subscription covering both programs is the only way to stop checking model years before quoting the job.
VI2, VI3, and J2534: What Plugs Into the Car
The software question is simple next to the hardware one. Nissan’s current interface is the Bosch-made VI3, and the older VI2 is still in plenty of toolboxes. Here is where each one works.
CONSULT-III plus. Connects through a VI2 or a VI3. Supports diagnostics, module programming, and key programming.
CONSULT 4. Connects through a VI3 only. Supports diagnostics and module programming. Key programming is not part of CONSULT 4.
CONSULT-III plus R2R and CONSULT 4 R2R. The right-to-repair versions of both programs, made for independent shops using J2534 hardware in place of Nissan’s own interface. They need a true third-generation J2534 device such as a CarDAQ-Plus 3 or the Nissan-specific Mongoose-Plus Nissan2. The VI3 does not work with the R2R software. You pick one path.
Two details trip up shops on the J2534 path. Nissan’s software expects the interface on COM port 1, and many generic J2534 devices show up as USB devices instead, so a pass-thru box that works fine with Ford or GM software may never be seen by CONSULT. And key programming on R2R is narrow: it covers the 2020 and newer Sentra and the 2021 through 2023 Rogue, and little else. Push-start key and BCM programming is limited to 2018 and newer vehicles no matter which software or interface you use.
If immobilizer work, ADAS target calibration, or CONSULT 4 vehicles are part of what you want from the subscription, plan on a VI3. The genuine interface also has the full EV diagnostic feature set and the ADAS calibration routines that the R2R path does not
